Best selling Floor heating from Devi
On this page you'll find a ranking of the best Devi products in this category. To give you a quick overview, we've already ranked the most important information about the products for you.
1. Devi Thin-bed heating mat 140F0418
Devi Thin Bed Heating Mat 140F0418
Manufacturer: Devi
Description: Thin bed heating mat 100 W/m², 2.5 sqm
Type: 140F0418
Design: Heating foil
With carrier mat: yes
Fixation of heating conductor: Glued
Self-adhesive: yes
Connection power: 250 W
Power: 100 W/m²
Heating conductor load: 11 W/m
Number of cold conductors: 1
Length of cold conductor: 4000 mm
Suitable for wet rooms: yes
Suitable as surface heating: no
Suitable as roof heating: no
Area: 2.5 m²
Length: 5000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: no
With room thermostat: no
With floor temperature sensor: no
Further details:
The thin bed heating mat comes with a connection cable and a suitable sensor protection tube DN10 with a red cap. The self-adhesive thin bed heating mat is pre-assembled for installation and has been specifically designed for embedding in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large rooms, as the return of the second connection is not required. The heating cable, with additional protective sheath for the use of RCD protection, is applied to a plastic mesh. The length of the connection cables is 4.0 m. Cold conductor: 1 x 4 m, 1.0 mm², Voltage: 230 V, Rated limit temperature: 120 °C, Specific heating output: 100 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10% / -5%, Minimum installation temperature: 5 °C, Minimum bending radius: 6 x dA, Calculation width: 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area 2.5 m², 0.5 x 5.0 m.
2. Devi Thin-bed set 300 W, 2.0qm 140F1652 with WLAN thermostat
Danfoss Thin Bed Set 300W 140F1652
Manufacturer: Danfoss
Designation: Thin Bed Set 300W
Type: 140F1652
With carrier mat: yes
Fixation of heating cable: glued
Self-adhesive: yes
Connection power: 0-300 W
Power: 150 W/m²
Heating cable load: 11 W/m
Number of cold conductors: 1
Length of cold conductor: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 2 m²
Length: 4000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: yes
With room thermostat: yes
With floor temperature sensor: yes
Danfoss Thin Bed Set 300W 140F1652: additional details
Thin bed set with Wi-Fi thermostat, flexible sensor protection tube DN10 with red cap, plastic nails, installation instructions. The self-adhesive thin bed heating mat with a connection cable is pre-assembled and has been specifically designed for installation in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor temperature system is particularly suitable for retrofitting in irregular and/or large rooms, as the return of the second connection is not required. The heating cable, with additional protective sheath for the use of RCD protection, is applied to a plastic mesh. The length of the connection cables is 4.0 m. Cold conductor: 1 x 4 m, 1.0 mm², Voltage: 230 V, Rated temperature limit: 120 °C, Specific heating power: 150 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10% / -5%, Minimum installation temperature: 5 °C, Minimum bending radius: 6 x dA, Calculation width: 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area: 2.0 m².
3. Devi Heating mat
Danfoss Heating Mat DTCE-300 4250W
Manufacturer: Danfoss
Designation: Heating Mat 400V
Type: DTCE-300 4250W
With Carrier Mat: No
Heating Cable Fixation: Glued
Self-Adhesive: No
Connection Power: 4250 W
Power: 300 W/m²
Heating Cable Load: 30 W/m
Number of Cold Leads: 1
Length of Cold Lead: 10000 mm
Suitable for Wet Rooms: Yes
Suitable as Outdoor Heating: Yes
Suitable as Roof Heating: No
Area: 14.8 m²
Length: 14800 mm
Width: 1000 mm
Thickness: 7 mm
With Controller: No
With Room Thermostat: No
With Floor Temperature Sensor: No
Danfoss Heating Mat DTCE-300 4250W: Additional Details
Ready-to-install heating mat with a connection cable suitable for installation in reinforced concrete, screed, or sand bed. Comes with additional protective sheathing for use with RCD protection. This heating mat system is particularly suitable for installation in angled and/or large areas, as the return of the second connection is not required. Includes factory-mounted waterproof connectors and a 10 m long cold lead, to be installed according to the installation instructions. Measurement of insulation and total resistance. Heating cable according to IEC 60800, Voltage: 400 V, Rated Limit Temperature: 80°C, Specific Heating Power: 300 W/m², Resistance Tolerance: +10% / -5%, Minimum Installation Temperature: 5°C, Minimum Bending Radius: 5 x dA, Protection Class: IP X7, Area 14.8 m², 4250 W.
4. Devi Thin-bed set 1350 W, 9,0qm 140F1661 with WLAN thermostat
Danfoss Thin Bed Set 1350W 140F1661
Manufacturer: Danfoss
Designation: Thin Bed Set 1350W
Type: 140F1661
With carrier mat: yes
Fixation of heating conductor: glued
Self-adhesive: yes
Connection power: 0-1350 W
Power: 150 W/m²
Heating conductor load: 11 W/m
Number of cold conductors: 1
Length of cold conductor: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 9 m²
Length: 18000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: yes
With room thermostat: yes
With floor temperature sensor: yes
Danfoss Thin Bed Set 1350W 140F1661: additional details
Thin bed set with Wi-Fi thermostat, flexible sensor protection tube DN10 with red cap, plastic nails, installation instructions. The self-adhesive thin bed heating mat with a connection lead is pre-assembled and designed specifically for installation in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor temperature control system is particularly suitable for retrofitting in awkward and/or large rooms, as the return of the second connection is not required. The heating cable with additional protective sheath for the use of RCD protection is applied to a plastic mesh. The length of the connection leads is 4.0 m. Cold conductor: 1 x 4m, 1.0mm², Voltage: 230 V, Rated limit temperature: 120°C, Specific heating power: 150 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10% / -5%, Minimum installation temperature: 5°C, Minimum bending radius: 6 x dA, Calculation width 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area 9.0 m², 0.5 x 18.0 m.
5. Devi Thin bed heating mat DTIF 140F0447 150W/sqm 2.0 sqm 0.5 x 4.0 m self-adhesive
Devi Thin Bed Heating Mat 140F0447
Manufacturer: Devi
Description: Thin Bed Heating Mat 150 W/m²
Type: 140F0447
Design: Heating foil
With carrier mat: yes
Fixation of heating conductor: Glued
Self-adhesive: yes
Connection power: 0-300 W
Power: 150 W/m²
Heating conductor load: 11 W/m
Number of cold conductors: 1
Length of cold conductor: 4000 mm
Suitable for wet rooms: yes
Suitable as surface heating: no
Suitable as roof heating: no
Area: 2 m²
Length: 4000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: no
With room thermostat: no
With floor temperature sensor: no
Additional details:
The thin bed heating mat comes with a connection cable and a suitable sensor protection tube DN10 with a red cap. The self-adhesive thin bed heating mat is pre-assembled and specifically designed for installation in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in angular and/or large rooms, as the return of the second connection is not necessary. The heating cable, with additional protective sheath for the use of RCD protection, is mounted on a plastic mesh. The length of the connection cables is 4.0 m. Cold conductor: 1 x 4 m, 1.0 mm², Voltage: 230 V, Rated limit temperature: 120 °C, Specific heating output: 150 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10 % / -5 %, Minimum installation temperature: 5 °C, Minimum bending radius: 6 x dA, Calculation width: 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area: 2.0 m².
Floor heating
EUR219,–
Devi Thin bed heating mat DTIF 140F0447 150W/sqm 2.0 sqm 0.5 x 4.0 m self-adhesive
6. Devi Heating tape in-line 10W/m 230V 50m 140F1223
The heating cable, pipe-mounted 10W/m 230V 50m 140F1223 from Devi is an efficient solution for heating pipes and other applications that require a constant temperature. With a heating power of 10 watts per meter, it provides a reliable heat source specifically designed for use in various environments. The product has a total length of 50 meters and is equipped with an IPX7 protection rating, making it resistant to water and moisture. This makes it ideal for use in damp or wet areas. The connection cable also has a length of 50 meters, allowing for flexible installation. Manufactured in Poland, the heating cable meets high-quality standards and is available in a striking red color. It is suitable for both private and commercial applications, helping to prevent frost damage to pipes and enhance the efficiency of heating systems.
7. Devi Thin-bed heating mat set 140F0824 1-900 W professional DTIF 6,0qm 50x120
Devi Thin Bed Set 1-900 W 140F0824
Manufacturer: Devi
Description: Thin bed set 1-900 W DTIF 6.0 m², professional
Type: 140F0824
With carrier mat: yes
Fixation of heating cable: glued
Self-adhesive: yes
Connection power: 0-900 W
Power: 150 W/m²
Heating cable load: 11 W/m
Number of cold leads: 1
Length of cold leads: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 6 m²
Length: 12000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: yes
With room thermostat: yes
With floor temperature sensor: yes
Additional details:
Thin bed set with touch thermostat, flexible sensor protection tube DN10 with red cap, plastic nails, assembly instructions. The self-adhesive thin bed heating mat with a connection cable is pre-assembled and specifically designed for installation in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large rooms, as the return of the second connection is unnecessary. The heating cable with additional protective sheath for the use of the RCD is applied to a plastic mesh. The length of the connection cables is 4.0 m. Cold lead: 1 x 4m, 1.0 mm², Voltage: 230 V, Rated limit temperature: 120 °C, Specific heating power: 150 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10% / -5%, Minimum installation temperature: 5 °C, Minimum bending radius: 6 x dA, Calculation width: 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area: 6.0 m², 0.5 x 12.0 m.
8. Devi Thin-bed heating mat set 140F0825 1-1050 W professional DTIF 7,0qm 50x140
Devi Thin Bed Set 1-1050 W 140F0825
Manufacturer: Devi
Description: Thin bed set 1-1050 W DTIF 7.0 sqm, professional
Type: 140F0825
With carrier mat: yes
Fixation of heating cable: glued
Self-adhesive: yes
Connection power: 0..1050 W
Power: 150 W/m²
Heating cable load: 11 W/m
Number of cold leads: 1
Length of cold leads: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 7 m²
Length: 14000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: yes
With room thermostat: yes
With floor temperature sensor: yes
The Devi Thin Bed Set 1-1050 W 140F0825 includes a thin bed set with a touch thermostat, a flexible sensor protection tube DN10 with a red cap, plastic nails, and installation instructions. The self-adhesive thin bed heating mat with a connection lead is pre-assembled for installation and has been specifically designed for installation in leveling compound or flexible adhesive directly beneath the floor covering.
With a low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large rooms, as the return of the second connection is not required.
The heating cable, with additional protective sheathing for the use of RCD protection, is applied to a plastic mesh. The length of the connection leads is 4.0 m.
Cold lead: 1 x 4m, 1.0 mm²
Voltage: 230 V
Rated limit temperature: 120 °C
Specific heating power: 150 W/m²
Length load: 11 W
Insulation: PVDF / FEP
Resistance tolerance: +10% / -5%
Minimum installation temperature: 5 °C
Minimum bending radius: 6 x dA
Calculation width: 50 cm
Delivery width: 48 cm
Mat height: 3.2 mm
Protection class: IPX7
Approval: EN 60335-2-96
Area: 7.0 m²
0.5 x 14.0 m
EAN: 5703466216590.
Floor heating
−7%
EUR880,– was EUR942,70
Devi Thin-bed heating mat set 140F0825 1-1050 W professional DTIF 7,0qm 50x140
9. Devi Heating cable DTIK-30 8.5m
Devi heating cable DTIK-30 8.5m
Manufacturer: Devi
Designation: Heating cable 267W 400V for asphalt
Type: DTIK-30 8.5m
Cable type: 2-core
Heating capacity: 30 W/m
Shielding: Braiding
Rated voltage: 400 V
Diameter: 8 mm
Height: 8 mm
Width: 0 mm
Length: 8.5 m
Colour: Black
Application: Open space heating
The Devi heating cable DTIK-30 8.5m is a ready-to-install heating cable with one connection lead, suitable for embedding in asphalt pavements. The heating cable fulfills the requirements of IEC 60800 and EN 62395. It features additional protective braiding for use with a residual current circuit breaker. The product includes a factory-fitted waterproof sleeve and a 10 m long PTC resistor.
Specifications:
- Voltage: 400 V
- Nominal limit temperature: 90°C
- Installation temperature: short-term 240°C
- Deformation resistance: 2000 N
- Tensile strength: 120 N
- Heating conductor insulation: FEP
- PTC resistor: 1 x 10 m 2.5mm²
- Specific heat output: 30 W/m
- Resistance tolerance: +10% / -5%
- Minimum installation temperature: 5°C
- Smallest bending radius: 5 x dA
- Protection class: IP X7
- Length: 8.5 m
- Power: 267 Wn
- EAN: 5703466192856.
10. Devi 140F1737 DEVImat200 200W/sqm 0.5 x 14.0 m Thin-bed heating mat
Danfoss Thin Bed Heating Mat 200 W/m² DEVImat #140F1737
Manufacturer: Danfoss
Description: Thin bed heating mat 200 W/m² 0.5x14.0m self-adhesive
Type: DEVImat #140F1737
Design: Heating foil
With carrier mat: yes
Fixation of heating conductor: Glued
Self-adhesive: yes
Power: 200 W/m²
Number of cold leads: 1
Length of cold leads: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 1.5 m²
Length: 14000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: no
With room thermostat: no
With floor temperature sensor: no
Danfoss Thin Bed Heating Mat 200 W/m² DEVImat #140F1737: additional details
The self-adhesive thin bed heating mat with a connection cable is pre-assembled for installation and has been specifically designed for embedding in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.5 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in complex and/or large rooms, as the return of the second connection is not required. The heating cable, with additional protective sheath for the use of RCD protection, is applied to a plastic mesh. The length of the connection cables is 4.0 m. Cold lead: 1 x 4m, 1.0 mm², Voltage: 230 V, Rated temperature limit: 120°C, Specific heating power: 200 W/m², Insulation: PVDF / FEP, Resistance tolerance: +10% / -5%, Minimum installation temperature: 5°C, Minimum bending radius: 6 x dA, Calculation width: 50 cm, Delivery width: 48 cm, Mat height: 3.5 mm, Protection class: IPX7, Approval: IEC 60335-2-96, Area: 0.5 m², 0.5 x 14.0 m.
