Best Danfoss products in the Floor heating category
On this page you'll find a ranking of the best Danfoss products in this category. To give you a quick overview, we've already ranked the most important information about the products for you.
1. Danfoss Electric Floor Heating ECmat
The Danfoss ECmat 100T is an electric underfloor heating system that enables efficient and even heat distribution in living spaces. With a heating power of 150 watts, it creates a pleasant indoor climate and is ideal for installation under tiles, laminate, or other floor coverings. The heating cables are 3 mm wide and are shielded with an aluminum cover foil, enhancing the safety and durability of the system. The ECmat 100T is designed to operate with an input voltage of 230 V and offers an IPX7 protection rating, making it particularly resistant to moisture. This underfloor heating system is a practical solution for anyone looking for a comfortable and energy-efficient heating option.
- Heating power of 150 watts for efficient heat distribution
- Aluminum cover foil to enhance safety and durability
- IPX7 protection rating for increased resistance to moisture
- Suitable for various floor coverings such as tiles and laminate.
2. Danfoss Heating mat 100W/sqm 840W 8,6qm 1Cold 83901912
Danfoss Heating Mat DTCE-100 840W
Manufacturer: Danfoss
Designation: Heating mat 230V
Type: DTCE-100 840W
With carrier mat: yes
Heating conductor fixation: glued
Self-adhesive: no
Connection power: 840 W
Power: 100 W/m²
Heating conductor load: 7.5 W/m
Number of cold leads: 1
Length of cold lead: 6000 mm
Suitable for damp rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 8.6 m²
Length: 11400 mm
Width: 750 mm
Thickness: 7 mm
With controller: no
With room thermostat: no
With floor temperature sensor: no
Danfoss Heating Mat DTCE-100 840W: additional details
Heating mat with a connection cable suitable for installation in or under the screed. Suitable for use in dry, damp, or wet rooms. With additional protective sheath for the use of RCD protection. This heating mat system is particularly suitable for installation in awkward and/or large areas, as the return of the second connection is not required. Including factory-installed waterproof connectors and a 6 m long cold lead, heating cable according to IEC 60800, voltage: 230 V, nominal limit temperature: 80°C, specific heating power: 100 W/m², resistance tolerance: +10% / -5%, minimum installation temperature: 5°C, outer diameter: 7 mm, minimum bending radius: 5 x dA, protection class: IP X7, area 8.6 m², 0.75 x 11.4 m.
3. Danfoss Heating mat 100W/sqm 500W 5sqm 1cold 11W/m 140F0422
Danfoss Thin Bed Heating Mat 140F0422
Manufacturer: Danfoss
Description: Thin bed heating mat 100 W/m², 5 sqm
Type: 140F0422
Design: Heating foil
With carrier mat: yes
Heating conductor fixation: glued
Self-adhesive: yes
Connection power: 500 W
Power: 100 W/m²
Heating conductor load: 11 W/m
Number of cold leads: 1
Length of cold leads: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 5 m²
Length: 10000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: no
With room thermostat: no
With floor temperature sensor: no
Danfoss Thin Bed Heating Mat 140F0422: additional details
Thin bed heating mat with a connection cable and suitable sensor protection tube DN10 with red cap. The self-adhesive thin bed heating mat with a connection cable is pre-assembled for installation and has been specifically designed for embedding in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large rooms, as the return of the second connection is not required. The heating cable, with additional protective sheath for the use of RCD protection, is applied to a plastic mesh. The length of the connection cables is 4.0 m. Cold lead: 1 x 4 m, 1.0 mm², Voltage: 230 V, Rated limit temperature: 120 °C, Specific heating output: 100 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10% / -5%, Minimum installation temperature: 5 °C, Minimum bending radius: 6 x dA, Calculation width: 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area 5.0 m², 0.5 x 10.0 m, EAN: 5703466203132.
4. Danfoss Heating mat 100W/sqm 350W 3.6sqm 1Cold 83901903
Danfoss Heating Mat DTCE-100 350W
Manufacturer: Danfoss
Designation: Heating Mat 230V
Type: DTCE-100 350W
With Carrier Mat: yes
Heating Cable Fixation: glued
Self-Adhesive: no
Connection Power: 350 W
Power: 100 W/m²
Heating Cable Load: 7.5 W/m
Number of Cold Leads: 1
Length of Cold Leads: 6000 mm
Suitable for Wet Rooms: yes
Suitable as Outdoor Heating: no
Suitable as Roof Heating: no
Area: 3.6 m²
Length: 4800 mm
Width: 750 mm
Thickness: 7 mm
With Controller: no
With Room Thermostat: no
With Floor Temperature Sensor: no
Danfoss Heating Mat DTCE-100 350W: additional details
Heating mat with a connection cable suitable for installation in or under the screed. Suitable for use in dry, damp, or wet rooms. Includes additional protective sheathing for the use of RCD protection. This heating mat system is particularly suitable for installation in angled and/or large areas, as the return of the second connection is eliminated. Includes factory-installed waterproof connectors and a 6 m long cold lead, heating cable according to IEC 60800, voltage: 230 V, rated limit temperature: 80°C, specific heating output: 100 W/m², resistance tolerance: +10% / -5%, minimum installation temperature: 5°C, outer diameter: 7 mm, minimum bending radius: 5 x dA, protection class: IP X7, area 3.6 m², 0.75 x 4.8 m.
5. Danfoss Heating mat 100W/sqm 150W 1.5sqm 1Cold 140F0416
Danfoss Thin Bed Heating Mat 140F0416
Manufacturer: Danfoss
Description: Thin bed heating mat 100 W/m, 1.5 sqm
Type: 140F0416
Design: Heating foil
With carrier mat: yes
Fixation of heating conductor: Glued
Self-adhesive: yes
Connection power: 150 W
Power: 100 W/m²
Heating conductor load: 11 W/m
Number of cold leads: 1
Length of cold leads: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 1.5 m²
Length: 3000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: no
With room thermostat: no
With floor temperature sensor: no
Danfoss Thin Bed Heating Mat 140F0416: additional details
Thin bed heating mat with a connection cable and suitable sensor protection tube DN10 with red cap. The self-adhesive thin bed heating mat with a connection cable is pre-assembled for installation and has been specifically designed for installation in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large rooms, as the return of the second connection is not required. The heating cable with additional protective sheath for the use of RCD protection is mounted on a plastic mesh. The length of the connection cables is 4.0 m. Cold lead: 1 x 4 m, 1.0 mm², Voltage: 230 V, Rated limit temperature: 120 °C, Specific heating output: 100 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10% / -5%, Minimum installation temperature: 5 °C, Minimum bending radius: 6 x dA, Calculation width 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area 1.5 m², 0.5 x 3.0 m, EAN: 5703466203071.
6. Danfoss Heating mat 100W/sqm 350W 3,5sqm 1Cold 140F0420
Danfoss Thin Bed Heating Mat 140F0420
Manufacturer: Danfoss
Designation: Thin Bed Heating Mat 100 W/m², 3.5 sqm
Type: 140F0420
Design: Heating Film
With Carrier Mat: Yes
Fixation of Heating Cable: Glued
Self-Adhesive: Yes
Connection Power: 350 W
Power: 100 W/m²
Heating Cable Load: 11 W/m
Number of Cold Leads: 1
Length of Cold Leads: 4000 mm
Suitable for Wet Rooms: Yes
Suitable as Outdoor Heating: No
Suitable as Roof Heating: No
Area: 3.5 m²
Length: 7000 mm
Width: 500 mm
Thickness: 3.5 mm
With Controller: No
With Room Thermostat: No
With Floor Temperature Sensor: No
Danfoss Thin Bed Heating Mat 140F0420: Additional Details
Thin bed heating mat with a connection cable and suitable sensor protection tube DN10 with red cap. The self-adhesive thin bed heating mat with a connection cable is pre-assembled and specifically designed for installation in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large spaces, as the return of the second connection is not required. The heating cable, with additional protective sheath for the use of RCD protection, is mounted on a plastic mesh. The length of the connection cables is 4.0 m. Cold lead: 1 x 4 m, 1.0 mm², Voltage: 230 V, Rated Limit Temperature: 120 °C, Specific Heating Power: 100 W/m², Length Load: 11 W, Insulation: PVDF / FEP, Resistance Tolerance: +10% / -5%, Minimum Installation Temperature: 5 °C, Minimum Bending Radius: 6 x dA, Calculation Width: 50 cm, Delivery Width: 48 cm, Mat Height: 3.2 mm, Protection Class: IPX7, Approval: EN 60335-2-96, Area: 3.5 m², 0.5 x 7.0 m, EAN: 5703466203118.
7. Danfoss Tilslutningssaet til kold kabel
Devi heating tape connection set 19805761
Manufacturer: Devi
Designation: Heating tape connection set
Type: 19805761
Type of accessory/spare part: Other
The Devi heating tape connection set 19805761 is a shrink sleeve connection set for heating tapes, designed for connecting flexible cold leads and heating tapes. It includes heat-shrink end termination. EAN: 5703466003886.
8. Danfoss Thin-bed set 525 W, 3,5qm 140F1655 with WLAN thermostat
Danfoss Thin Bed Set 525W 140F1655
Manufacturer: Danfoss
Designation: Thin Bed Set 525W
Type: 140F1655
With carrier mat: yes
Fixation of heating conductor: Glued
Self-adhesive: yes
Connection power: 0..525 W
Power: 150 W/m²
Heating conductor load: 11 W/m
Number of cold conductors: 1
Length of cold conductor: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 3.5 m²
Length: 7000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: yes
With room thermostat: yes
With floor temperature sensor: yes
Danfoss Thin Bed Set 525W 140F1655: additional details
Thin bed set with Wi-Fi thermostat, flexible sensor protection tube DN10 with red cap, plastic nails, installation instructions. The self-adhesive thin bed heating mat with a connection lead is pre-assembled and specifically designed for installation in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large spaces, as the return of the second connection is not required. The heating cable with additional protective sheath for the use of RCD protection is mounted on a plastic mesh. The length of the connection leads is 4.0 m, cold conductor: 1 x 4m, 1.0 mm², voltage: 230 V, rated limit temperature: 120°C, specific heating output: 150 W/m², length load: 11 W, insulation: PVDF / FEP, resistance tolerance: +10% / -5%, minimum installation temperature: 5°C, minimum bending radius: 6 x dA, calculation width: 50 cm, delivery width: 48 cm, mat height: 3.2 mm, protection class: IPX7, approval: EN 60335-2-96, area: 3.5 m², 0.5 x 7.0 m.
9. Danfoss Heating mat 150W/sqm 1050W 7sqm 1cold 11W/m 140F0454
Devi Thin Bed Heating Mat 140F0454
Manufacturer: Devi
Description: Thin bed heating mat 150 W/m², 7 sqm
Type: 140F0454
Design: Heating foil
With carrier mat: yes
Fixation of heating conductor: glued
Self-adhesive: yes
Connection power: 0 to 1050 W
Power: 150 W/m²
Heating conductor load: 11 W/m
Number of cold conductors: 1
Length of cold conductor: 4000 mm
Suitable for wet rooms: yes
Suitable as outdoor heating: no
Suitable as roof heating: no
Area: 7 m²
Length: 14000 mm
Width: 500 mm
Thickness: 3.5 mm
With controller: no
With room thermostat: no
With floor temperature sensor: no
Additional details:
Thin bed heating mat with one connection cable and suitable sensor protection tube DN10 with red cap. The self-adhesive thin bed heating mat with one connection cable is pre-assembled for installation and has been specifically designed for embedding in leveling compound or flexible adhesive directly beneath the floor covering. Due to its low installation height of only 3.2 mm, it is ideal for renovating and modernizing bathrooms, showers, kitchens, etc. This floor heating system is particularly suitable for retrofitting in awkward and/or large rooms, as the return of the second connection is not required. The heating cable with additional protective sheath for the use of RCD protection is applied to a plastic mesh. The length of the connection cables is 4.0 m. Cold conductor: 1 x 4 m, 1.0 mm², Voltage: 230 V, Rated limit temperature: 120 °C, Specific heating output: 150 W/m², Length load: 11 W, Insulation: PVDF / FEP, Resistance tolerance: +10 % / -5 %, Minimum installation temperature: 5 °C, Minimum bending radius: 6 x dA, Calculation width 50 cm, Delivery width: 48 cm, Mat height: 3.2 mm, Protection class: IPX7, Approval: EN 60335-2-96, Area 7.0 m², 0.5 x 14.0 m.
10. Danfoss Outdoor heating 300W/q 3675W 12qm 83902083
Danfoss 83-902083 Heating mat 3675W.
